Search results

Hello, Can the tuner out 1/4" jack on the back of the effects gizmo be programmed in the editor to be open and closed? I have a real Leslie 122 that I'm trying to incorporate and because there isn't a signal being sent back to the gizmo from the Leslie, i don't think it'll work properly if...

Received my stickers. Thank you so much! Next question; can any of the other loops on the Effect Gizmo, outside of loops 9-12 be used to control function switches/tap tempos?

Ok. Make sense. Let me reach out to them. Btw- how would a guy who has a lot of your product go about getting a few RJM stickers sent to him?

Hello again! GT22 HX One Lehle Dual Expression I figured out how to control parameters of the HX One within the Expression control page using the Lehle but it is controlling every preset "parameter 1". Can those be programmed to vary between presets. Meaning, can i control MIX on my preset...

OK. Thanks i have the supa puss's working. I can't seem to get my HX One, which is connected to the PBC Mastermind not my effects loop rack, to communicate tap tempo. It's connected via MIDI using the same tap tempo button. It is communicating, but for some reason the tap tempo isn't working...

I think i have to do momentary?! Because when going Action Type "Audio" That is only going to be designated to the PBC and these will be plugged into the Effects Gizmo, which operates my effects loop of the amp.

Ok. So would it be as simple as? IA Action Type: Audio Subtype: Loop number 9 or is that programmed CC values under Action Type: CC Momentary?

Hello, I have a RJM PCB10 and I'm routing the midi channel out to an effects loop on top of my amp in which I use the 12U effects gizmo. In that effects loop is two Way Huge Supa Puss that accept External Tap Tempo and i would like to have these programmed on the PBC to my designated tap...

Great! Thank you. One last question. The back of the EG on the power it says 9VAC or 12VDC. If it’s ran @12VDC how many mA does it draw?

On the 12 loop Effect gizmo, due to position, I’m curious if any of the effects in loops 1-8 are hitting the tuner out signal or if that’s clipped to the input jack and bypasses all of the loops?

I figured it out. Had to turn on audio loop 7 in setup mode as it didn’t default there like it should have (per manual). We’re rocking!

I wouldn’t even know where to begin on that. Any ideas where that breakdown could be? Is there something on the Global page that needs to be checked/switched? I’ll be home to check on the operation but I’m 99% it doesn’t turn on when programming via right click > assign CC -> cc#X, or the...

So I’m not home to check but let’s run through two scenarios so I can troubleshoot when I get home. Scenario 1 - no they do not turn on Scenario 2 - they do turn on What’s next steps for either.

Ok. So in doing this, it appears the signal is being sent and it is functioning as intended. Now how do I incorporate the Mastermind to control?

So this is what I have programmed. It’s in Loop 9/NO and it doesn’t appear to be working. These operate as a latching function switch, unless Momentary is check, correct? Do you see anything incorrectly programmed?

Any cable requirements here? Standard TS cable work? Not working as described. Have it in “output NO”. Maybe it should be in the “send loop” so it’s sending signal?

Beautiful! If I use output 9 as a function switch that controls the “hold” function on a DM2000 what does the programming look like in the editor when I’m editing a specific button.

Can the Effect Gizmo be used for function switches. I don’t see dedicated spaces like on the back of the PBC Mastermind I have loops 1-6 being used but want to be able to use it for function switching like the “hold” feature on an Ibanez DM2000.

Ok. So i tried a lot this weekend. Did NOT try your recs here, but the first thing i tried was to pull my Mini Effects gizmo out and see if I could just end up getting audio to pass through it. After trying a bunch of different combinations, I now have audio pass through, but get this... I have...

Yes, guitar > CAE. Bypassing RJM completely. Not overly relevant just making sure you had all information available. I will try your recommendations and report back asap. Thanks for the help here.