Search results

Yeah....i'm surprised as well. I did get the cable in bulk from redco and it was all from the same roll, so i guess its possible i got a bad batch or something. Is there any brand/model cable you find works well or that you use most often for the longer 20ft type runs? I find it's much more...

Well damn....I would have never thought this but it's starting to look like it's the Mogami 2524 I run to and from the loop. Swapping it out for some monster cable I had, and the monster sounds much more neutral. The Mogami seems to pinch the bottom end and brighten the top end when I tried both...

Another good suggestion I didn't think of.... I'll try both and see what happens.

I've had the PBC since it was released and recently i happened to be playing with out it in the loop (straight into the amp, nothing in the loop) and noticed how much better the amp sounded. Mainly in the lower frequencies, ie the PBC or possibly just the extra amount of cabling to run from the...

Not sure if anyone can help here, but we have a Roland SPD-SX drum pad/sampler we use live for samples, backing tracks and a click (run to in-ear monitors). I have all the songs we play programmed into the PBC and I'd like to be able to send a midi clock message to the Roland SPD-SX to set the...

I think it's actually the H9 is very poor at multi-tasking. It apparently can't execute its midi messages at the same time it's passing on messages to downstream devices. All i did was change the device order in the PBC editor and NOT the physical order on my board. My H9 is still right in the...

Update.....i re-ordered the device list in the PBC, putting the H9 last, and that seemed to fix the issue. Played three 1 hour sets last night with no glitches. So i guess that is a work-around for Eventide pedals with flakey midi-thrus.....

I'm fairly sure it's the H9. I'm transitioning from rack based effects to pedalboard effects and have had my midi chain longer than this with no issues. Previously during this transition it was: PBC - modfactor - Timefactor - GCX - Eventide GTR 4000 - TC G-Major - Triaxis. Never any issues...

Anyone have an Eventide H9 and have problems with downstream midi devices not getting, or getting garbled midi messages? I believe its an H9 issue and not a PBC issue....but was wondering if anyone has had the issue and what you did to resolve it. MIDI signal chain is as follows: PBC -...

If you end up making an iOS version, see if you can make it work with older iPads (like gen 1's) if possible. I use an old gen 1 iPad for Eventide H9 editing. The gen 1 iPads top out at version 5.1.1 i believe and can't handle iOS 6 or above.

An update....i ended up not using the Behringer unit as i found it was causing signal attenuation. Not sure if it was the unit i had was defective (it's pretty old and has been bounced around a lot) or if that is just how they are. I re-routed all the audio cables away from all the power cables...

Perfect Thanks!

I do the majority of my preset editing in the editor. Curious if there is an easy way to also set the audio loops to on/off using the editor. I've tried adding an action to the preset using the following type of action (which i'm assuming is the correct one?): Action type: Audio Subtype...

I was looking more for when you change banks or songs that it would blink through the presets on that page before you initially choose one. That way if i go to song 3, i can visually see it scroll through (or blink through) the presets i have for that song instead of having to remember "on this...

Preset scroll in setlist/song mode.....or just preset scroll period regardless of mode....

Ok so i picked up an ISO 5. Powering it from that made no change. Sounded the same as when i was using the PowerFactor (Cioks). What i did try that seemed to work was i had a Behringer HD400 Hum Destroyer laying around and added that between the 5-6 out and the Triaxis input and also between A...

I've powered it with either the power supply from one of the Eventide pedals, which is 12v and 1200ma i believe....and also with an Eventide PowerFactor version 1 (Cioks) 12v outlet. I haven't tried using 7-10 in front of the amp. I've used 7-10/out A in the loop and i dont notice any noise...

I tried some different cables and different outputs on the PBC and one interesting thing is if i go in to the 1-4 input and out the A output, so all 10 loops in front of the amp.....the amount of hiss added is crazy. Switch back to either of the other outputs, 1-4 out or 5-6 out, and its back to...

It's almost like a ground loop kind of sound. I recorded it with a video camera. The camera leveled out the without/PBC (made a bit louder) and the with/PBC (made a bit quieter) so they sound like they are the same volume on the clip.....but the 2nd half of the clip starting at ~:36 second mark...

I've noticed that when i run through the PBC i have an increased noise floor. I have it setup with the first 6 loops in front and the last 4 in the loop. Even when only running the front 6 (with none of the loops on) the noise floor is increased. I've tried turning off the buffers and such but...