Search results

Strymon tech actually had me lift the ground of a midi cable in my rig amd it solved the same issue on my board.

Hey Everyone. I have a question on Expression pedal behavior and best practices. I have the exp set up on my PBC to control the Mix on my Timeline and Big Sky. I did this to try and free up presets in both the strymon units. That way if i have a preset with a HALL verb and a TAPE Echo, and i...

Issue Resolved. Found a work around.

Ron, Seems to work except for the univibe. Its in an external loop and does not shut off when going back to any of the mobius sounds. Still experimenting with behaviors. Thanks

Hello everyone, Im currently trying to get a button page i have created to behave correctly, and i'm sure I'm missing something. Here is what i am trying to achieve. I have essentially 5 sounds on the Mobius that i use a LOT. On this button page are 5 buttons that use an IA action to turn...

I did that. Did not follow timeline. Tested cables again on loop 9. Low and behold, a small solder burr had poked through the plastic sleeve on inside of plug. Ring (right) had shorted to sleeve. Resolved at last. Thanks.

Nope. Certain they are both out. Mono to stereo switch is out. Stereo output switch is out. Just as described in manual: Cables were tested prior to install. I will test again this evening. Are the cables i described above correct in application?

Im ashamed to admit that i am back here for more schooling as my stereo pedals are not behaving as predicted. Have a look at what i have going on and if i have done something wrong. Loop 7 is a Caverns. It is mono in and out. Im using a ring diconnect to feed it, and a mono to stereo...

Resolved. Found another thread here that solved it. This forum is super.

Are there any mastermind users successfully controlling a morningstar ML5 with cc toggle commands? I have set up a button page and have control of the individual loops, but the selected and stored loops are not recalling with presets correctly. Not sure what i am doing wrong. Thanks in advance.

It was option 1.

I am having a similar issue. When i change pbc presets, it changes presets on the morningstar mc8. Did you ever find a solution on this?

I had a feeling that might be the case. Man, swapping the programming for the mobius change is tremendous. I probably have several hundred presets with the mobius on it...uhg. Unless you know of a way to bulk edit. I will literally have to go through presets 1 at a time and make the same...

I too would buy this. Simple Button expander with LED's

Hello Ron, Starting a rebuild on my big board, and want to revisit this. I have Keeley caverns v2 in loop 7 running stereo, mono side of Strymon mobius in loop 8 (run it in pre/post mode), timeline stereo in loop 9 and big sky stereo in loop 10. Let me see if i have this right: Caverns...

Yeah, that is pretty much the size of it, but i have made a few changes. Im going to use a morningstar mc8 as a "slave" and a morningstar ml5 as the added loops, controlled from the pbc. Should be here next week.

Hey All, I know there are some clever folks in this forum so here goes. I want to expand my PBC10. My 10 loops are full and i would love to have more loops, but also more buttons for instant access while using preset page. I am researching how to do this. I know i could add an a mini...

Hey Ron, Happy Holidays. Having a new issue with the tap tempo and my mobius. It cropped up after updating firmware on all the strymons. I have the mobius set to store tempo per preset, but i also send tap to it and my timeline. It used to work fine to adjust tempos of songs if they push...

RON, I just loaded this file to create the midi edit page as you directed and IT WIPED THE PBC CLEAN. Gone. ALL GONE. So i reloaded my settings, and it overwrote the file i loaded from the thumb. Ideas here? Im so glad i had the foresight to back up first. Thanks, John