Phisherman
New Member
Not sure where to post this, so I'm putting this here.
I have a Mastermind, and just purchased a Mini Effects Gizmo (5 loop version). For full disclosure, I'll give my entire setup then explain what I'm trying to do.
PBC Setup:
3 Button Pages currently
- Presets (exactly that)
- Loops (1 through 10)
- Switches (amps/presets on midi pedals)
The Signal:
Guitar>Wah>Cali76>PBC
Loop 1: Tru Tron 3x
Loop 2: Pog 2
Loop 3: Tri/Ram Muff
Loop 4: The Dude > KOT
Out: Spaceman Mercury IV
Loop 5: Wombtone Phaser
Loop 6: Flanger
Out: M5 Modeler > Deluxe Memory Man > EP3 (all in/on rack)
Loop 7: Echosystem
Loop 8: Monument Trem
Loop 9: Ventris Reverb
Loop 10: Rotary/Ditto X2
Output 1: Marshall Amp
Output 2: Fender Amp
The Goal:
I would like to place the Effect Gizmo in the out section between loops 6-7. So instead of it looking like this:
Out: M5 Modeler > Deluxe Memory Man > EP3
It would look like this:
Out: Mini Effects Gizmo
Loop 1: M5 Modeler
Loop 2: DMM
Loop 3: EP-3
Loop 4: Empty
Loop 5: Empty
The Question(s):
1) Will this even work?
2) Will I be able to control the units connected to MEG via the PBC since they are in an out loop?
3) How do I set this up in the editor? (trying to set all MEG pedals to be controlled on new button page, Page 4, specifically for these 5 loops called "Rack")
Thank you in advance! I hope I have explained this properly. I attached my current PBC settings.
I have a Mastermind, and just purchased a Mini Effects Gizmo (5 loop version). For full disclosure, I'll give my entire setup then explain what I'm trying to do.
PBC Setup:
3 Button Pages currently
- Presets (exactly that)
- Loops (1 through 10)
- Switches (amps/presets on midi pedals)
The Signal:
Guitar>Wah>Cali76>PBC
Loop 1: Tru Tron 3x
Loop 2: Pog 2
Loop 3: Tri/Ram Muff
Loop 4: The Dude > KOT
Out: Spaceman Mercury IV
Loop 5: Wombtone Phaser
Loop 6: Flanger
Out: M5 Modeler > Deluxe Memory Man > EP3 (all in/on rack)
Loop 7: Echosystem
Loop 8: Monument Trem
Loop 9: Ventris Reverb
Loop 10: Rotary/Ditto X2
Output 1: Marshall Amp
Output 2: Fender Amp
The Goal:
I would like to place the Effect Gizmo in the out section between loops 6-7. So instead of it looking like this:
Out: M5 Modeler > Deluxe Memory Man > EP3
It would look like this:
Out: Mini Effects Gizmo
Loop 1: M5 Modeler
Loop 2: DMM
Loop 3: EP-3
Loop 4: Empty
Loop 5: Empty
The Question(s):
1) Will this even work?
2) Will I be able to control the units connected to MEG via the PBC since they are in an out loop?
3) How do I set this up in the editor? (trying to set all MEG pedals to be controlled on new button page, Page 4, specifically for these 5 loops called "Rack")
Thank you in advance! I hope I have explained this properly. I attached my current PBC settings.