Recent content by Clibbus International

  1. C

    On Board Global Loop Bypass?

    Sounds good, thank you!
  2. C

    On Board Global Loop Bypass?

    Hey all, I am curious if there is a way to globally bypass a certain loop from the PBC unit while preforming in a setlist? For instance if a pedal or connection in a pedals loop begins to misbehave during a performance you could go to the loops page and remove it from all presets globally for...
  3. C

    Firmware Update Question

    Awesome, thank you!
  4. C

    Firmware Update Question

    My apologies if any of this has already been covered. I am about to go into a tour with a guitarist next week, unfortunately we do not have any rehearsals to go through editing/ updates etc. They have a set up with the PBC 10 that is running Firmware version 4.3. -Has there been any issue...
  5. C

    Strymon Pedals And Pbc 10 Question

    I have a friend trying to set up his pbc 10 and sending PC commands to A Mobius>Timeline>Big Sky All the Device channels are selected (1,2,3) And On each pedal Midi channels are correlating.I have read about the offset for changing each bank and preset (00A, 00B, Etc..) He seems to still be...
  6. C

    PBC Attenuating Signal

    Figured it out, was a bad joint in my guitar in passthrough connector the one connection I mistakenly overlooked. Whew. Thanks for the help, yall are great over here.
  7. C

    PBC Attenuating Signal

    Switches are set to Mono, Effects are in loops 7 and 8 are mono. A delay and chorus but only using Mono outputs on the pedals. Also this is happening with all loops off and just going clean to the amp. I am assuming there is no way in the editor to access the line mixer? I also tried swapping...
  8. C

    PBC Attenuating Signal

    Buffer 3 is on, With other amp unplugged the issue is still the same
  9. C

    PBC Attenuating Signal

    Also Have tried different cables, and when plugged direct in to the amp the volume was normal.
  10. C

    PBC Attenuating Signal

    Running Two Amps out of PBC and even with dry signal, the JC 120 seems to be drastically attenuated, getting much lower volume than it should any clue?
  11. C

    PBC A/B Output Pan Percentage?

    Ahh no I was using TRS. In doing this how would I wire the Volume pedal to drop in line to control the panning of loops 8 and 9? Would it just be Loop 7 Send TRS-> Input A of VP , Loop 7 Return -> Insert Cable And TIP/RING to each of the outputs?
  12. C

    PBC A/B Output Pan Percentage?

    I apologize I meant to say it went to both amps when in heel position or neither in toe position.
  13. C

    PBC A/B Output Pan Percentage?

    Yeah I Had 2 TRS Cables For the Pan pedal in Loop 7 and tried both Ts and TRS cable for the fuzz pedal in loop 8 tried it with both stereo function pushed in and out and it would only send to one amp.
  14. C

    PBC A/B Output Pan Percentage?

    Got it, that did not seem to work either, as the pedals in mind were a fuzz and a comp sustain. Really pullin' my hair on this one The chain Goes as follows Guitar in loops 1,2,and 3 (OD,WHAMMY,TREM) Loops 5 and 6 Are Chorus and Delay 7,8 and 9 Are Comp, Bass Synth, and Fuzz. I am just trying...
  15. C

    PBC A/B Output Pan Percentage?

    Alright And now the tables have turned. The client has now requested if possible to make so the two amps can be in an a/b/y configuration where the output could be overidden by the pan pedal. IE If both amps are running simultaneously one could be driven more than the other. At first thought it...
See more
Back
Top