I ended up selling the H90 and returning to the HX stomp. It was way too much power and complicated to use as a simple Swiss army knife of FX. I also like to use reverb and delay along with FX at times and I would have to morph one of the Algos on the H90 to use as Rev/Dly in one side and the...
Thank you ! So send from one of the loops 4-6 to input 1 on the H90 and Output 1from H90 to the Return of one of the loops from 4-6? I had to enable the insert loop on all my presets with the HX to setup Pre or Post FX do I do the same here? SO enable Insert loop on my preset and lets say I'm...
I'm replacing my HX stomp with an Eventide H90 on my board. I used the HX mostly for effects and not the amp models and speaker cabs etc. What is the best way to connect the H90 to the 6X? I had the HX stop wired as below so I could use the preamps and fx wherever I wanted to in the chain...
Just redoing my board a little and when I was hooking up the power supply ( Voodoo Lab 3 Plus ) I rechecked the MA of the 6X and it said power either 9 or 12 VDC 220 ma. I have the option for 9 or 12 VDC. What is the difference of running one over the other? Is 12VDC optimal? I had been running...
How do you save individual presets on the 6X? I am using an HX stomp with my 6X and would like to save presets I have made from these two connected so when I do a gig I can load them from a folder on my MAC into any preset slot open the 6X. I figured that saving the 6X preset is the way to do...
- Are you using an Axe-Fx or other multi effect not pictured here?
No I have the HX stomp and 6X hooked up with the 4CM into a Mesa Boogie Fillmore
- Do you have anything plugged into the PBC's MIDI jack or USB jack normally?
Only the HX stomp is plugged into the 6X via MIDI
- How is...
I gigged with my PBC/6X for the first time last night. At random times it would just jump to a high number preset in the 300s. I had to turn it off and on again 3 times mid song during my set to reset it. Once it powered back up it was back to my presets and was fine until it happened again. I...
Need some more clarity as I am sitting down and programming the HX. Just want to make sure I have it right. In the PBC editor in the presets section, The + sign in the loop order represents the insert loop? So as per your instructions: First I set up the HX stomp patch with an FX Loop block...
Thank you ! Can I setup multiple PCs at once? In other words if I wanted to keep Delay and Reverb from the HX on all my presets with the global option under audio , can I also set a PC for an effect like a flanger on an individual 6X preset while the global is still assigned to it? So Lets say...
First time MIDI user. I have my HX wired up 4CM in loops 5 and 6 and INS. Looking for any newbie tips in accessing FX and programs of th HX via the 6X. I know that in the editor I can add the HX to the Devices. Do I have to change any other values to the HX, 6X, or Editor to communicate between...
OK great Thank you . So to clarify if I just want to run time based fx from the HX ( dly, rvrb, chorus) in the loop of my amp I would put them after the FX block in the HX, enable the Insert loop on the PBC, and Enable loop 6 ? Loop 6 would always be at the end of the PBC chain after the Insert...
Is this correct? I am assuming this will allow me to put the put the HX anywhere in the chain as well as putting fx pre or post as long as I have an FX loop block in my HX presets with FX assigned accordingly to where I want them?
Is it possible to use both the EXP and VOL IN/OUT simultaneously on the DVP5 ? I am trying to figure out the best way to hook it up to the RJM PB6X and HX Stomp. By simultaneously I just meant using the outputs the same time to send to two different units. I could use the expression to control...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.