Search results

So, I have no idea if this is even possible, but it would be cool to be able to set the signal to fade in when turning off the tuner. This way you could be looping a drone in a PBC loop, and fade it in rather than have it begin suddenly. Probably not possible, but worth asking.

A slight tangent: Is there a reason you want the Muffuletta not to follow a buffer? My board has both a Muffuletta and a Fuzz Face-type pedal. The Muffuletta sits in Loop 3 of my PBC, after the first buffer, and it works just fine. Fuzz Faces, on the other hand, don't work well after a buffer...

Thanks Ron!

Hi folks, I picked up a MEG to add a few more loops to my PBC. It works great! In the MEG I have a Clinch FX EP-PRE (always on), and a compressor (on 95+% of the time). I was wondering if there was an easy way to set the MEG loops for these pedals to be on by default to save me having to...

Thanks again Ron, I'll look forward to this hopefully being an update in the not too distant future. Honestly, best customer service ever, I'd just about recommend a PBC on that basis alone. Peace, Matt

That's why I couldn't get it to work then! Thanks Ron. P.S. It would be a great addition for a future release. In my case, I'm using a TimeLine and a H9, and knowing which pedal I'm currently controlling with the exp pedal by looking at the LED would be helpful.

Could the LED be turned on and off to signal which pedal is being used in the pedal group? Or is that not possible, say, for a future update?

Hi Ron, Quick question: how do you control the LED on the SP1-RJM used through a PBC? It's connected to both the exp pedal and ext switch inputs via TRS, but I can't seem to figure out how to set the LED. I've tried setting On and Off colours in the Ext switch settings window, but that doesn't...

A drive that has TS expression control is the Moog MF Drive. The exp controls the filter.

Yeah, that makes sense. But will things always happen in order for commands related to the PBC?

Excellent, thanks. Any recommendations for a good quality and small isolation transformer? Does the GoodWood Output have isolated L and Rs?

Probably a dumb question, but I don't much understand ground loops. If I have the two outputs from the PBC running into a pedal (in my case, a Strymon Flint that's always on), will the pedal negate the isolation of the two outputs when running PBC > stereo pedal > amps? Thanks!

I've never thought about this, but this thread raises a question for me, Ron. If you have more than one IA action on a button, does it perform them simultaneously, or in order of their placement on the IA list?

I had to check lol. But my tip was meaningless without Ron's advice to remove Page 1's name.

Happened on mine also. I'm on Sierra. Also back to 3.1.6 without issue.

Close, but switch the order. Preset Name | Song Name

Perfect. You must get sick of dealing with all these issues. Thanks for your patience! Just out of interest (to help me better understand my PBC), would "Update on Preset Change" have any effect either way in this case? I understand why "Send on Preset Change" would cause me the problem I had...

Here's my settings. I don't think that particular issue is the case, partly because it suddenly stopped working mid-gig, partly because I tried the "Send Redundant PCs" setting when I was getting it fixed and it did nothing. Also, would that be the case if each patch I tried had a different PC...

It's quite possible, although I'm hard-pressed to explain, if the issue is indeed with the H9, why a) Changing the PBC device slot of the H9 fixed the issue, and b) why my Timeline didn't work in the same PRBC device slot. I had the H9 on MIDI channel 2, and changing it to another channel while...

Hi folks, Today while using my board, I noticed that my PBC had stopped sending PC messages to Device 1, which in my case is an Eventide H9. It continued sending CC messages just fine. When I got home, I played around trying to fix the issue. I even factory reset my H9, which didn't help, and...