Search results

Is there a way to scroll through my overture presets via my PBC6x controller? In the editor and manual, there is no CC for up preset or down preset? This makes it very difficult to program on the fly (my timeline, ventris and terraform all have two buttons for each device, up and down. Then I...

Currently i have 'preset 2nd press' set to alternative, because in a few songs I need 5 presets and the PBC6x only has 4 switches. This has been very useful. However in a particular song, I would like to have a few presets when pressed for the 2nd time engage my klon loop (loop 2). I would like...

Hi there, I have a PBC6x. It currently has a stereo chorus in loop 6. (Mono send, stereo return) I want to swap the pedal out for a mono flanger, but I don't want to replace the cable being used. I would prefer to leave the split TRS cable in place for the very likely event I revert to a stereo...

Hi everyone I'm trying to configure my Global Preset to have 4 pages available to scroll through, while all other presets only have 2. Is this possible? My normal presets are for all my songs, and the second page gives loop access for changes on the fly. The global preset is for when im...

Any chance of one in the future? I find I travel more and more without a laptop, and just an ipad. Would be super handy if I could still access the editor with it. I know thats not a simple question, just curious if any plans. Cheers

When I am creating presets on the PBC, I use page 2 (the loops page) to select my loops. The only change I made to this page is loops 8, 9 and 10 don't turn on the loop, but rather take you to a new page dedicated for the MIDI effect in that loop. IE Loop 8 has a Boss MV500, when I press loop 8...

Can I have a preset not only recall a Delay patch on my timeline, but have it send a BPM to the timeline to be automatically changed to. It would save me having to change preset and then tap tempo the time in. IE say I have a delay on patch 01A on my timeline currently set to 88bpm When I...

I am not sure how to best control the BOSS multi effect pedals with my PBC. I would like to use the MD500 in A/B simul mode where I can toggle two effects on at a time in series. But I would also like to have presets on the PBC within my songs select only 1 effect at a time and toggle off...

When I have a PBC preset that uses the Timeline, if I manually turn the timeline off using the strymon pedal rather than the PBC, when I change to a new preset on the PBC the timeline stays in bypass mode. It loads the new delay preset but i have to re-press the strymon bypass switch to get...

I would like to have a page setup for a series of IA buttons (similar to the default page 2), though some of the buttons I would like to be grouped (so it turns off the previous loop when activating another). Currently it is in page 5 of the attached file. (It is accessed by 2nd pressing a...

This is a slightly updated file from my other post (now the timeline is using PC offset). I'm using a timeline and a boss rv500 with my PBC. I have the timeline set for Midi channel 1 and the RV500 for 2. I have created 2 sets of buttons on page 4 (accessed by hitting the 'Switches' button)...

Currently I have my global preset found by second pressing the active preset (rather than a dedicated button). Is there a way to have the global preset (when activated) to automatically switch to page 2 on the PBC? The idea is to have the global preset set up as no loops on (direct to amp)...

Hi Guys, I currently have page 1 setup fairly similar to the default config of the PBC, page 2 is loops as per normal and page 3 is switches. I created a page 4 for Midi control stuff (timeline and reverb pedals) but I have a unique request for page 5. I would like to create a bottom row of 6...

im having an issue where trails mode is unchangeable via the PBC menu for some loops. When I switched a loop to parallel and then went to activate trails it doesn't allow me to change the setting. I had trails yesterday (new to the PBC) but today when I created an additional parallel loop it...

Hey guys, I just got my PBC and I have quite a few questions about loops 7>10 still, despite reading most of what I can find online about them. Inc the manual ;) I play in stereo, almost always. I plan to use three stereo effects and one mono effect in these loops: - Mono analog delay w kill...

Hi guys, I am about to purchase a PBC and have obviously spent a large amount of time researching how to set it up and what features I would like to make use of. I have read the sticky thread a number of times about using loops 7>10 with mono and stereo pedals (and the cables you might need)...