Recent content by cgscotto

  1. C

    IA Problem/One Control-Fixed with GigRig Remotest Loopy 2

    Just an update. I finally received the GigRig Remotest Loopy 2. I replaced the One-Control with the Loopy 2. Set the Loopy 2 to the midi channel I was using for the One-Control, and replaced the One-Control CC numbers in all the buttons with the corresponding Loopy 2 CC numbers. First try and...
  2. C

    IA Problem/One Control-Fixed with GigRig Remotest Loopy 2

    Thanks for the reply. I agree that it is a bewildering choice to control both loops using one CC number. I tired turning on Direct Send PC/CC, but everything remained the same. While both loops work when using the IA switches, only loop 1 will turn on when it is set to turn on in a preset. The...
  3. C

    IA Problem/One Control-Fixed with GigRig Remotest Loopy 2

    OK, my previous problem has been solved, but may be related to the current problem. I am using a One-Control stereo loop pedal to switch between two boost pedals. A side note, I wish RJM made a two loop switcher because I know I would not be having these problems. The MEG is just a bit too much...
  4. C

    IA Button/Preset Programming Problem

    HI, thanks for the reply. I have IA link selected on all the buttons performing the same function. Also, Ron told me (I don't know if this is Ron responding) not to Send on Preset Change and Update on Preset Change turned on when using these as just CC toggles. I can see doing that with the...
  5. C

    IA Button/Preset Programming Problem

    Thanks for the quick response. File is attached.
  6. C

    IA Button/Preset Programming Problem

    It has been a while since I have had an issue that I have not been able to find a solution. However, this one has me stumped. I have a One Control two loop pedal in my rig. The One Control has midi functionality with either PC change or CC control. I am using CC control. I named the device OC...
  7. C

    For those controlling a slightly bigger setup with the "small" GT10: how do you use your controller?

    I am using a GT10 in a rig that has Mark VII and JP-2C heads, an Axe-FX III, and an H90. I could easily use the real estate of the GT22 to give me more immediate access to functions on all the units, but I like the size of the GT10, so I got creative with programming buttons, pages, and IA Mode...
  8. C

    Scene Names on Preset Page

    UPDATE: The issue of the scene names not displaying has not happened recently. I don't think I did anything different, but the issue seems to have resolved itself. Perhaps it was caused by a midi communication problem that I inadvertently fixed or may I changed an LT setting without realizing...
  9. C

    Scene Names on Preset Page

    I have an AX3 scene page setup on the LT. I have show scene names checked on the global page. I also removed the name from the scene page. As it should, the page displays the preset name at the top (where "Presets" used to be) and the scene name appears at the bottom where the preset name used...
  10. C

    7-Pin Midi and Nixie Software

    UPDATE: in case anybody is using a similar setup. Also, I should state that I am using the AXFX3 with the 4cm and a JP-2C amp as well as using the AXFX3 output 1 to studio monitors when I want to use amp modeling. Original setup: I was using a Midi Solutions Merger box to send the output of the...
  11. C

    7-Pin Midi and Nixie Software

    OK, by looking at some older threads from when Nixie was first released, I was able to find a solution to the problem of Nixie not displaying or finding the Timeline when using a 7-pin midi cable from the Phantom power box with both midi input and outputs connected to the Phantom power box...
  12. C

    7-Pin Midi and Nixie Software

    First, sorry for another problem post. I am just going through reworking a couple of rigs to make them a bit more efficient by incorporating an Axe-FX III as the effects unit with the amps. So far everything has been great and the two phantom power box I ordered really help make everything much...
  13. C

    Can't Add CC Action

    Thank you! At least I know I am not imagining the problem or that something was wrong with my LT. You also answered my other question, why was it working with my second rig with an Axe-Fx III and a Mastermind LT? Well, in the rig in which it works, the Axe-Fx III is first in the device list. I...
  14. C

    Can't Add CC Action

    Hi, yes I am using editor 4.9.1 and running the latest firmware on each device. I don't see a Select CC button. Like I said, if I use the mouse right click, I can select from a menu and it works. I am including three screenshots of trying to add a CC action. As I said, I can also do it manually...
  15. C

    Can't Add CC Action

    OK, this is driving me nuts. First, I am using a Mac with 12.6. If I try to add a CC action for the Axe-Fx III or for the Collider in the Mastermind LT editor using the right click on the mouse, everything works fine. However, if I double click the button, set it to IA, and then try to use Add...
Back
Top